sstore sstore

ANVER

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 2,001 total)
  • Author
    Posts
  • in reply to: Air flow #19538
    admin
    Participant

    How can I calculate the available air flow and output pressure from the following situation:A reservoir measuring 6.6CF receives an additional 59.4CF of air every cycle. Within sixteen cycles, the pressure in the tank reaches 2030psi by my calcu

    in reply to: Help wanted Getting solemoids to work #19540
    admin
    Participant

    Hi!I 'm using a SMC solenoid VQ1131y-5-C4 for a robotic snake sculpure. THe problem is I can't get the solenoid to switch from outlet B to A. It got a flatt ribbon connector. When I apply voltage trough the ribbon connecter and a air pressure of

    in reply to: Help wanted Getting solemoids to work #19541
    admin
    Participant

    Supply air on the P" port? Is it an external pilot? Does it switch when you press the little orange manual over-ride?Look at http://www.smcworld.com and contact the nearest office and ask them. It's often too dificult to sum up in an e-mail."

    in reply to: AIR FLOW #19543
    admin
    Participant

    WAHT IS THE MAX AIR FLOW @14 PSI I CAN GENERATE FROM A COMPREESOR RATED AT 90CFM @125PSI

    in reply to: automated valves for chlorine wanted #19545
    admin
    Participant

    looking for 500 or more 3/4 valves per year for swimming pool chemicals. Will only consider electrically actuated. Must be under $ 100. we tried solenoids and they have too many problems. plastic valve and actuator preferred."

    in reply to: Air Reservoir capacity and loacation #19574
    admin
    Participant

    Dear Friends,Is there any formula or criteria by which we can decide the location and capacity of an air reservoir?I need an answer very urgently. This is going to help me in analysing the pneumatic system setup at my plant.Thank u in advance.

    in reply to: requirement for SMC make pneumatic components #19515
    admin
    Participant

    Please contact SMC India. They can help you

    in reply to: Air Reservoir capacity and loacation #19575
    admin
    Participant

    Try these siteshttp://www.pyebarker.com/TechTips/techtip3.htmhttp://air.irco.com/asg/air_system_info/air_system_information.aspBud

    in reply to: Airmatic – Allied #19476
    admin
    Participant

    Dear Sir,We have an inquire for 10 pcs of Airmatic-Allied, Inc.valve but didn't have detail P/N. Just have its Kit No.: 1501 12 tha valve paper packing had shown 321404-25So pls quote subj valve:1. Ait to close 10 pcs2. Air to open 10 pcs3.

    in reply to: Resume for Suitable Post in Pneumatic Industry #19512
    admin
    Participant

    Send your resume detailsJob in Pneumatic Tools and TechnologyMaterial Handling – PneumaticLocation – Pune

    in reply to: Looking for switch #19577
    admin
    Participant

    I am looking for a Pressure Switch Effector 0-100 Bar PN-100-SBR14-QFPKG/US/V P/N PN7022. I do not hagve the manufacturer, but if anyone could direct me in the right way…I would appreciate it.

    in reply to: Counterbalance (Overcenter) Valve #19579
    admin
    Participant

    Is there such a thing as a PNEUMATIC Counterbalance (-or- 'Overcenter') Valve?I need to pneumatically rotate ~1000# mass, 180 degrees in 2 to 3 seconds. The rotational axis is parallel to the ground and NOT about the machines Center of Gravity.

    in reply to: Counterbalance (Overcenter) Valve #19580
    admin
    Participant

    Larry;There is no Over Center valve for air circuits that I know of. Have you considered an Air-Oil circuit? Go to http://www.pneumatic-source.com to see a chapter out of a Fluid Power Training book I have put together to see if one of the methods there

    in reply to: Actual Lift Force of A Meter Out Circuit #19491
    admin
    Participant

    Hi Tom,One easy way to do this would be to install a second flow control of the same size and type at the exhaust port of the valve controlling the cylinder, with a tee between the valve and flow control for installation of a gauge. Then you could

    in reply to: Looking for switch #19578
    admin
    Participant

    Hi SaraBeth,I believe the brand name is Effector. I did a search on the web and comae up with a pile of hits. Way too many to sort. You should have no trouble finding it.

Viewing 15 posts - 16 through 30 (of 2,001 total)