seltecuae

ANVER

Forum Replies Created

Viewing 15 posts - 661 through 675 (of 2,001 total)
1 … 44 45 46 … 134
  • Author
    Posts
  • November 26, 2004 at 12:00 am in reply to: Pneumatic impulse wrench manufacturer is looking for distributors worldwide #19752
    admin
    Participant

    Dear Sirs,We are Pneumatic Impulse Wrench manufacturer in taiwan, now we are devleoping our market worldwide and looking for worldwide distributors and agents.Our impulse wrench ( oil pulse wrench )is high quality and stable and durable. our mod

    November 26, 2004 at 12:00 am in reply to: CPOAC SELENOID #19281
    admin
    Participant

    Dear Sir I need information abouth selenoid and where should I buy?data is,03-100%fm48v,50hz,7.8VA48V.60Hz,5.8VA24V cc 5.1 wattEVU dia 1.50.98;12bar32NF

    November 29, 2004 at 12:00 am in reply to: compressor discharge flow, various units used #20697
    admin
    Participant

    Some our customer ask for air compressor with capacity Nm3/min, pls tell me what is the difference between Nm3/min and m3/min? Thanks

    November 29, 2004 at 12:00 am in reply to: Automation Studio #19753
    admin
    Participant

    Has anybody got a copy of either the pneumatics or hydraulics libraries and electrical control libraries for Automation Studio 5

    December 2, 2004 at 12:00 am in reply to: Stainless Steel water seperator #19761
    admin
    Participant

    Try Norgren's F22 range

    December 2, 2004 at 12:00 am in reply to: Need inline filter canister #19755
    admin
    Participant

    PIAB has filter cannisters .8 and 1.6 gallons for filtering vacuum http://www.piab.com

    December 2, 2004 at 12:00 am in reply to: Job's in Canada #19738
    admin
    Participant

    iam mechanical power engineering ,graduated from alexandria university in egypt with grade good at 2003

    December 2, 2004 at 12:00 am in reply to: Looking for miniature high pressure solesoid valve. #19734
    admin
    Participant

    For a valve for this applicationcontact MAC Valves 1-800-MAC-VLVS

    December 2, 2004 at 12:00 am in reply to: Looking to control Halloween props #19719
    admin
    Participant

    Don't use electric, use compresses air, cylinders and valves.

    December 3, 2004 at 12:00 am in reply to: electropneumatics #19763
    admin
    Participant

    pls help. i need to know about the basics of electropnuematics. i want to acquire basic skills. thank you.phone +63 918 7241295

    December 3, 2004 at 12:00 am in reply to: booster relay #19705
    admin
    Participant

    Purpose of volume booster is to provide higher volume of output to the control valve, which in some cases, the positioner cannot cater.In your case the booster relay is to be connected in between positioner out put and control valve.Then the valve

    December 4, 2004 at 12:00 am in reply to: miniature HP pressure gauge for air 3-4000 psig #20788
    admin
    Participant

    We are the manufacturer of miniature pressure gauge in China.

    December 6, 2004 at 12:00 am in reply to: electropneumatics #19764
    admin
    Participant

    Pneumatics Online is now offering online training. Various courses are available. Go to http://www.training.pneumaticsonline.com to register at a minimal cost. Electropneumatics is covered in the course on pneumatics. Hope this helps!

    December 7, 2004 at 12:00 am in reply to: REQ – Small solenoid vavle needed. #19765
    admin
    Participant

    Hello,I’m wondering if you can help me? I’m looking for a small solenoid valve for use in a personal project (pneumatic launcher). I haven’t had any success tracking down these parts on the internet so far. I was wondering if you guys/ladies

    December 12, 2004 at 12:00 am in reply to: schematics #19769
    admin
    Participant

    Hi kevin- iam also a beginner of pneu. can you send me full details-i can tryoutREGARDS

  • Author
    Posts
Viewing 15 posts - 661 through 675 (of 2,001 total)
1 … 44 45 46 … 134