Davelfc64

ANVER

Forum Replies Created

Viewing 15 posts - 556 through 570 (of 2,001 total)
1 … 37 38 39 … 134
  • Author
    Posts
  • March 8, 2004 at 12:00 am in reply to: Need a low pressure switch/relay, non-electric #19587
    admin
    Participant

    Does anyone offer a device that would sense the pressure on a tank(or actually the loss of pressure to be more specific. i.e. less than 1/2 psig on decreasing)then allow a secondary air line to open? It to be used as a safety measure to only al

    March 9, 2004 at 12:00 am in reply to: crouzet solenoid valves #19591
    admin
    Participant

    I need information about how to get representative office to Crouzet solenoid as part number 81 513 100

    March 10, 2004 at 12:00 am in reply to: Air Valve – 3 Way #19594
    admin
    Participant

    I need a 3 or 2 1/2" 3-Way Ball Valve. Brass body

    March 10, 2004 at 12:00 am in reply to: Air Valve #19593
    admin
    Participant
    March 11, 2004 at 12:00 am in reply to: 3-Way Air Valve + Air Line Loss #19598
    admin
    Participant

    I need a 3 3-way air valve

    March 11, 2004 at 12:00 am in reply to: Auto Switch to Backup Air Supply #19596
    admin
    Participant

    I need to design a backup air supply system that automatically valves itself in based on dropping pressure w/o electrical power. Normal pressure would be 90-100 psig. I'd like the backup to kick in around 80 psig. The valve would have to be meta

    March 12, 2004 at 12:00 am in reply to: 3-Way Air Valve + Air Line Loss #19599
    admin
    Participant

    We have three way valves up to 2-1/2 http://www.rosscontrols.com/PDFs/27Sol.pdfWe have also made a 3" Lockout valve. It contains two parallel 2" valves in one assembly with the ability to lock it out for OSHA 1910.147 requirements. I can email"

    March 15, 2004 at 12:00 am in reply to: 3-Way Air Valve + Air Line Loss #19600
    admin
    Participant

    ALKON also has a line of valves up to 2-1/2 NPT in the Bazooka Series.www.alkoncorp.com419-333-7000Best regards."

    March 17, 2004 at 12:00 am in reply to: wira fittings #19602
    admin
    Participant

    we are looking for the wira fittings agents in Australia

    March 24, 2004 at 12:00 am in reply to: ATEX #19604
    admin
    Participant

    Has anyone run across ATEX yet?

    March 31, 2004 at 12:00 am in reply to: 3-way valve for vacuum application #19607
    admin
    Participant

    We are looking for a small (3×2"max)3-way valve that would allow us to manually switch a vacuum source from one inlet to another. Ideally it would be spring loaded so we could normally operate off of ports 1 & 2 then when a button is depressed"

    April 1, 2004 at 12:00 am in reply to: Ceramic iso valves #19612
    admin
    Participant

    Does anyone know where I can purchase iso valves that have ceramic spools,besides Parker.

    April 1, 2004 at 12:00 am in reply to: ZINC BODIED FILTERS #19610
    admin
    Participant

    Can anyone assist me. I am in search of a supplier that can provide me with inline filters 1/4-2" that is zinc bodied material."

    April 1, 2004 at 12:00 am in reply to: 3-Way Air Valve + Air Line Loss #19601
    admin
    Participant

    A cheaper method might be to use an actuated ball valve. 3 L ported ball valves are available with either electrical (slow… typically 12-20 secs) or with pneumatic actuation (reaction of around 1 sec) via either a double acting or single actin"

    April 8, 2004 at 12:00 am in reply to: Eracon MCN10-35 #19617
    admin
    Participant

    Hello! Need exact replacement for this cylinder. Port positioning is critical. The replacement recommended by New Era will not work as there is not enough clearance in the machine for the speed control. Any good ideas?Thanks!

  • Author
    Posts
Viewing 15 posts - 556 through 570 (of 2,001 total)
1 … 37 38 39 … 134