admin

ANVER

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 2,001 total)
1 2 3 4 … 134
  • Author
    Posts
  • March 5, 2000 at 12:00 am in reply to: I need help! #19583
    admin
    Participant

    Can you help me? I needsome data on pnematics.

    March 7, 2000 at 12:00 am in reply to: Tamper-proof pneumatic door lock #19402
    admin
    Participant

    I used to sell cylinders and valves to a company called Maple (Stockport, England) who made security systems for vehicles. one of which was just the type of item you are looking for.Regards Jim

    March 9, 2000 at 12:00 am in reply to: Help wanted Getting solemoids to work #19542
    admin
    Participant

    Having the air supply on the proper port is probably your culprit. The air should go on port #1, or P"

    March 9, 2000 at 12:00 am in reply to: Counterbalance (Overcenter) Valve #19581
    admin
    Participant

    Hi Larry,You have an interesting application, and before I comment on it, I would like to know more about how you intend to rotate the mass, and what your plans are for dealing with it etc. when you reach the end of your rotation.What you do with

    March 16, 2000 at 12:00 am in reply to: Rubber hand squeeze bulb pump #19359
    admin
    Participant

    I have bulb pumps with two check valves that are black pvc corrosive resistant material available in bulk pack for $3.62 each. Reply to Staninvent@cox.net

    March 17, 2000 at 12:00 am in reply to: Low Pressure Air Tanks #19530
    admin
    Participant

    Look at Clippards air-volume tanks. Aluminum and SS construction.

    April 7, 2000 at 12:00 am in reply to: Which One? #19516
    admin
    Participant

    What hydraulic symbol do you need?

    April 22, 2000 at 12:00 am in reply to: Counterbalance (Overcenter) Valve #19582
    admin
    Participant

    This is just an idea:Just before you get to the over centre point, have the pressure sensed in the side that is in the lifting side.At or maybe just before, the overcentre point, put the same pressure into the other side.It might be simpler put s

    May 5, 2000 at 12:00 am in reply to: Martonair Pneumatik Valve #19480
    admin
    Participant

    VALVE MARTONAIR CM1762A/152+SPB3221§§POWER SUPPLY:220V/50HZ PROCESS CONNNECTIONS:1/4 BSP WITH ENDPLATE§§NP/16216. Please state current Manufacturer Part No and Manufacturer Product type No. R. Elmar"

    May 21, 2000 at 12:00 am in reply to: schrader bellows valve #19528
    admin
    Participant

    Dear Sir, I am looking for the valve c/w base.Part No. 962200145 12VDCIf you would locate a supplier from Malaysia or Singapore, I would be very pleased.Thanks

    August 23, 2000 at 12:00 am in reply to: AGRIPEX #19534
    admin
    Participant

    Looking for a UK distributor for agripex air cylinders part number i think 5012-12-1-c50

    September 12, 2000 at 12:00 am in reply to: Air Reservoir capacity and loacation #19576
    admin
    Participant

    Go to CAGI on line an they will have the info on cfm/acfm an storage volume but you will need the cfm of compressor you have a screw compress is about 5cfm per hp. Recp. are 3-4Cfm per hp. Also pipe size can have an effect. Most times i put as

    October 12, 2000 at 12:00 am in reply to: Metric Seals – Metric O-Rings – Any Size – Shipped Fast #19497
    admin
    Participant

    Looking for 2,500pcs of 29.5mm x 2mm Buna 70.Need parts tomorrow. Please respond quickly

    October 27, 2000 at 12:00 am in reply to: Pneumatic Valves #19298
    admin
    Participant

    Please contact me.or visit http://www.regada.skT:00421 51 74 80 464

    October 30, 2000 at 12:00 am in reply to: Cascade Circuit Design #19522
    admin
    Participant

    I need to design a cascade circuit that a machine will clamp a piece of metal, drill, and eject the drilled job

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 2,001 total)
1 2 3 4 … 134