admin

ANVER

Forum Replies Created

Viewing 15 posts - 211 through 225 (of 2,001 total)
1 … 14 15 16 … 134
  • Author
    Posts
  • June 27, 2002 at 12:00 am in reply to: low cost metallic or glass "check valve" device #20398
    admin
    Participant

    Sourcing a single-use" device that will readily engage with and seal very thin wall(.008 ich) aluminum or stainless steel

    June 28, 2002 at 12:00 am in reply to: rotay vane motor #20407
    admin
    Participant

    I need to find supplier of 2 rotary vane motors , one .75 HP approx 1300 rpm and one 3 HP approx 1300 rpm.Please help

    July 1, 2002 at 12:00 am in reply to: rotay vane motor #20408
    admin
    Participant

    Try Ingersoll-Rand.

    July 2, 2002 at 12:00 am in reply to: Static Residual Pressures #20413
    admin
    Participant

    HELP! HELP! HELP!PLease E-mail me only!Please Help!Can someone tell me what the differences of Static & Residual pressures are?EMAIL ME AT:TMCKEE@ULTRADYNAMICS.COM

    July 3, 2002 at 12:00 am in reply to: Static Residual Pressures #20414
    admin
    Participant

    If I remember correctly, the rail industry uses these terms throughout their specifications. Again, if I remember correctly, the static pressure is pressure in the system and residual is left in the lines after exhaust. The way a brake system wo

    July 5, 2002 at 12:00 am in reply to: Static Residual Pressures #20415
    admin
    Participant

    The (very) old Westinghouse air brakes used a triple valve. When they worked they worked great when they did not they were unsafe at any speed.Newton

    July 8, 2002 at 12:00 am in reply to: rotay vane motor #20409
    admin
    Participant

    Atlas Copco can help you.www.atlascopco.comRegards.

    July 11, 2002 at 12:00 am in reply to: U-seal piston design #20421
    admin
    Participant

    Visit these 2 sites. http://www.applerubber.comwww.parker.comBoth are excellent resources.

    July 11, 2002 at 12:00 am in reply to: U-seal piston design #20420
    admin
    Participant

    I have to design a piston equipped with U-seals. Can I get a web address of a site that deals with the information needed to calculate and design the inner parts and the seal grooves?Thanks in advance

    July 11, 2002 at 12:00 am in reply to: Summer Robotics Project #20416
    admin
    Participant

    I am a high school student taking an extra credit class in robotics. I was given a bunch of equipment to assemble into a machine of my choice.I am looking for any suggestions I can get. I was given a controller that has 4 outputs. To boot, I

    July 12, 2002 at 12:00 am in reply to: AIR FUSES #20422
    admin
    Participant

    Does anyone know who sells/manufactures airfuses besides Norgren.I am in australia and looking for large qtys from 1/4'-1/2 size."

    July 12, 2002 at 12:00 am in reply to: Micro or miniture solenoid valves #20106
    admin
    Participant

    for the smallest valves check http//www.pneutronics.com

    July 17, 2002 at 12:00 am in reply to: pneumatic counters #20430
    admin
    Participant

    LOOKING FOR A SOURCE FOR A SOURCE FOR AN INEXPENSIVE, PREDETERMINING COUNTER W/PNEUMATIC OUTPUT; OR LONG RANGE (15 MIN.) PNEUMATIC COUNTER. THANKS.

    July 17, 2002 at 12:00 am in reply to: Cheap Products #20426
    admin
    Participant

    I have been noticing low cost air valevs on the site. Jiontair.com has some darned low prices. Why the valve priecs so low?I done some bulding lately and dont' know if they are good. What the differense between them and Pnumatics brand I done

    July 18, 2002 at 12:00 am in reply to: SCFM of FRL #20369
    admin
    Participant

    Marlene,A lot of good information has been offered up on this subject already, but I think that there is one remaining point that makes the distinction between providing Cv vs SCFM for valves and frls. Directional valves (not ball or globe types)

  • Author
    Posts
Viewing 15 posts - 211 through 225 (of 2,001 total)
1 … 14 15 16 … 134